Home > Ironing Centers > IronAway Ironing Centers >

Ironaway A46 In Wall Ironing Board

Ironaway A-46 Built In Electric Ironing Center
Ironaway A-46 Built In Electric Ironing Center, Birch Door
Ironaway A-46 Built In Electric Ironing Center
Ironaway A46 In Wall Ironing Board - A461AU
Ironaway A46 In Wall Ironing Board - A461AU
Ironaway A46 In Wall Ironing Board - A461AU
Ironaway A46 In Wall Ironing Board - A461AU
Ironaway A46 In Wall Ironing Board - A461AU
Ironaway A46 In Wall Ironing Board - A461AU
Ironaway A46 In Wall Ironing Board - A461AU
Item #: A461AU
Retail: $708.09 Price: $429.52
You Save: $278.57 (39.3%)
What side would you like the hinge?

Door Type

Would you like a 180 degree swivel?

Accessory Options:

In Wall Ironing Board IronAWay A46

Choose the IRON A WAY Model A 46 In Wall Ironing Board, with extra length to replace existing boards, premium length 46 inch ironing board with cover and pad and telescoping steel support legs. The easy, 4 inch height adjustment lets you choose the most comfortable work position for your ironing board. The A 46 In Wall Ironing Board includes: A solid state silent timer that turns on power to the built-in work light and the electrical outlet. You can leave your iron plugged in at all times, even when the door is closed. A built-in safety switch disconnects all power when the ironing board is in the upright position.This In Wall Ironing Board cabinet is made of solid poplar, a hot iron storage compartment, accessory shelf, pilot light and garment hook are all standard, making the A46 our most complete in wall ironing board and center for the longest board in the industry and best for replacement upgrades. Rough Dimensions 14 1/4 W" x 59 7/8"H x 3 7/8"D Finished Dimensions 15 W x 60.5/8H x 6 7/8 D. Install center 26 from floor would put the board height at 33". You may want to lower or raise that depending on your height.

46 Inch In Wall Ironing Board

  • Comes standard door birch veneer door unfinished with multi-density fiber board under the veneer.
  • Power timer and outlet.
  • 4" Height adjustment.
  • Ironing Board Cover and Pad are included for 46" board
  • The interior has been painted a cool gray.
  • Telescoping steel support legs for longer board
  • 2 Storage Shelves 9 1/4 long 3 5/8 wide .

    Surface Mounting:
  • Unit may be surface mounted (unit extends approximately 6 7/8" into room) or recessed (unit extends approximately 3" into room) into any wall with standard 16 inch center studs.
  • See table in specification sheet (above) to determine desired ironing board height above the floor usually. The user can adjust height of board after installation with a 4" differential between a maximum and minimum height.

  • Simple Install! Identify the location, cut and remove the drywall, slip the unit between the studs and attach it with the installation screws provided.
  • All models are per-assembled and ready to install.
  • Fits between standard 2 x 4 studs on 16" centers. Install at the height of your choice, typically 34"-36" from the floor.
  • Rough Dimensions 14 1/4 W" x 59 7/8"H x 3 7/8"D
  • Finished Dimensions 15 W x 60.5/8H x 6 7/8 D
  • Wall to end of board when down 50 1/4

  • 120V, 15 Amps.
  • Pigtails are provided in bottom of wire way for hookup to supply line. Make entrance into knockouts provided in top and bottom of wire way through left-hand vent hole.

  • Swivel Option (Rotates Ironing Board 180�)
  • Extra replacement Cover Pad
  • Hinge Hardware
  • Iron
  • Sleeve Board
  • Surface Mount Trim Kit
  • In Wall Ironing board
    White Flat MDF Covered on Poplar Door
    Flat Maple is Stain or Paintable Unfinished Door
    Maple is Raised Unfinished Maple Wood Door
    Oak is Raised Unfinished Wood Door
    White is Raised and Finished Door

    Mirror has a 1/4 Plated Glass with Polished Edge Finish Stainless top and botton sides raw unfinished.

    In Wall Ironing Board IronAWay A46

    Technical Specs

    Electric Standard
    Finished Dimensions
    15 W x 60.5/8H x 6 7/8 D
    Installation Type Recessed, Surface Mount
    Light /Timer/Outlet
    Optional Garment Bar Standard
    Optional IronRowenta Optional
    Optional Sleeve Board Optional( will not fit into Ironing Center when closed
    Rough Dimensions
    14 1/4 W" x 59 7/8"H x 3 7/8"D
    Swivel Board Optional sold as
    Timer Standard
    Voltage 120
    Wall Opening Depth 3. 7/8
    Wall Opening Height 59.7/8
    Wall Opening Width 14.1/4
    Warranty Limited One Year

    Installation Guide

    Standard Features

    • 46" Ventilated Board W/4" Vertical Adjustment
    • Premium Hot Iron Storage
    • 60 Minute Solid State, Silent Timer
    • Additional Storage Shelves
    • Full Length Piano Hinge
    • Ironing Board Cover and Pad
    • Electrical System
    • Hot Iron Rest
    • Electrical Cord Cover & Restraints
    • UL Listed
    • Garment Bar
    • Spotlight/Less Bulb
    • Unfinished Flush Birch Door
    • Built-In Safety Switch
    • Fully assembled and ready to install

    Optional Features

    How do we get replacement cover and pads?

    Ironing Board Cover and Paid is a standard feature on all units. Replacement cover and pads can be obtained directly from IRON-A-WAY. In fact, you can order online right now!

    If we don�t order the swivel now, can we get it later?

    The swivel is not a retrofit item. Since it utilizes more interior space due to its rugged undercarriage, the frame on a swivel cabinet is deeper than cabinets without swivels. For this reason, swivels must be ordered at the time of purchase and cannot be added later. Where applicable, all other options available on the ironing centers can be added after the original purchase.

    Can we order the ironing center without a door?

    �No Door� option is one of the available options. If selected, the unit will arrive without a door allowing you to match custom cabinetry. When this option is selected the piano hinge and door hardware is not included with the unit. This is done so you can match hardware with your cabinetry.

    Does the door come pre finished?

    All wood doors come unfinished so you can customize your unit to match the room d�cor. Interior has been painted a cool gray saving you hours of unnecessary finishing time.(NE-242 with white flat door comes standard with white interior and exterior color.)

    What are the door dimensions?

    Door dimensions for all models except the A-46 and AL-42 are 15� W X 47 7/8�. The Model A-46 and AL-42 door dimensions are 15" X 60 5/8�.

    Can the door be hinged on the left side?

    Yes, all units may be ordered with a left-hand hinge at no additional charge. All units come standard with a right-hand hinge. (As you face the unit the hinge is on the right-hand side of the cabinet.)

    Will it hold all irons?

    The hot iron storage area is designed to hold the majority of all major brands of irons with the exception of very large, specialty irons designed for the sewing industry.

    What is the warranty?

    One-Year Limited Warranty from the date of purchase. Warranty covers all defective parts returned to factory for replacement, other than light bulbs, installed units, finished or stained doors, ironing board cover and pad. The warranty does not include labor for installation or replacement.

    Can the board swivel before it is lowered completely into the ironing position?

    No, the board must be completely lowered before the board can be swiveled.

    Is the white colored door a paintable surface?

    The white flat door is melamine. The white raised panel is a thermo foil. Both are a finished surface not intended for paint.

    Steam ironing removes creases faster than dry ironing because when fabrics are damp the fibers are open so the creases haven't taken hold.

    Do the ironing centers fit between the studs?

    All models, except the NE-242 (surface mount), are designed to fit between standard 2� x 4� studs on 16� centers.

    Can the ironing center be installed at any height?

    One of the benefits of owning an ironing center is you can have it installed at your desired ironing board height. However, most ironing centers seem to be installed with a 34� � 35� ironing board height. From the floor 22"set center in wall, that would put your board at 40" off the floor. or 18 inches set center would put board at 36" off the floor.

    Are the ironing centers difficult to install?

    The ironing center is very easy to install. The product basically requires identifying the desired location, cutting and removing the drywall, slipping the unit between the studs and attaching it with the installation screws provided. All units are pre-assembled and ready to install.

    Are the electrical models hard to wire?

    Electrical models are pre-wired so they only need to be pigtailed with the incoming electrical wire. The pigtails are located at the bottom of the electrical raceway. All electrical work must be done in accordance with all applicable electrical codes. Electrical models utilize 15 AMPS.

    Where does the electrical wiring enter the ironing center?

    The electrical models contain a raceway that has an knock-out for entry of the house's electrical wire at the top of the raceway.

    Can the ironing center be recessed into a cabinet rather than in a wall?

    The ironing center can be recessed into a cabinet. Since your cabinet will have the door, you simply purchase your ironing center without a door. However, the door dimension for the model of your choice is very important since it determines the opening size requirement for your cabinet. An added tip for this type of installation is to purchase the surface mount trim and add it to the ironing center prior to installation in the cabinet.

    The surface mount package trims out the sides of the ironing center so they are flush on all four sides. This will make the installation into the cabinet easier and quicker.

    Is the wood on the cabinet frame that extends into the room when recessed or the entire cabinet when surface mounted pre-finished?

    The exterior of our cabinets, as well as our doors, are unfinished so that you can stain or paint to match your d�cor.

    Do most homes stain the cabinet frame to match the door or do they match the cabinet frame to the wall?

    This is really a matter of choice but it would be typical that the cabinet frame matches the ironing center door.

    Can I make my ironing center flush with a wall or cabinet?

    You can make your ironing center flush with the wall or the cabinet provided that the depth of the wall or cabinet is equal to the depth of the ironing center. Irons by themselves require more depth than a typical 2"x4" wall so unless you customize the installation, the ironing center will extend into the room some distance.

    Can the ironing center be installed into metal studs?

    This type of installation can be completed, but you will need to use mounting screws designed for use with metal studs. Additionally, given the design of metal studs, in your rough-in opening, one stud will need to be trimmed out with a piece of wood to fill the cavity designed in the bend of the metal stud.

    Do all the units have to be recessed?

    With the exception of the NE-242, all cabinets are designed to be recessed mounted. However, all models can be surface mounted. When doing so, we recommend adding the surface mount trim package (except on the NE-242) so your cabinet sides are flush with the cabinet frame.

    Frequently Asked Product Questions

    What type of wood do you use in making your ironing centers?

    The cabinet frame is made of poplar and the door is dependent upon the what you select. (i.e. Oak, Maple, Pine.) We use poplar for both its ease of use in construction, but also its ability to match color when staining doors of other wood species (i.e. Oak, Maple, Pine.)

    Where is the electrical outlet to plug in the iron?

    The electrical outlet is at the bottom of the raceway where it is out-of-sight and more conveniently placed when using your ironing center.

    Can I add an electrical raceway to my non-electric model?

    You can add our electrical raceway to a model NE-342 but not to our Model NE-242. Additionally, by adding any other kind of electrical parts (other than an IRON-A-WAY raceway) to either model nullifies your warranty and we are not responsible for any damage it may cause to your ironing center or your home.

    What is the recommended size of the light bulb?

    We recommend a 30R20 with a standard base and 2 1/2" diameter. This bulb is available at most stores that sell light bulbs.

    Does all the door hardware come with the no-door option?

    No door hardware comes with the no-door option since it's assumed that the installer will desire to match other cabinet door hardware.

    Can you paint either the white flat or white raised panel door?

    Painting either the white flat or white raised panel door is not recommended. The flat Maple door is recommended when painting a flat style door and when painting a raised panel door the determination is made on the desired grain of wood. Each door will show a slightly different texture. Oak has a more open grain, Maple more closed and Pine a softer wood.

    What irons fit into the ironing center?

    The ironing centers being produced today contain an over sized storage area and hold the majority of irons being sold today. If you own an ironing center that was purchased many years ago, given the changes in the styles of steam irons, please contact our customer service for specific iron models that will store within your ironing center.

    Is the hot iron rest different from the hot iron storage?

    The hot iron rest is a feature that allows you a place to rest the iron while turning your garment. The hot iron storage is the place where you store your iron when you are ready to fold-up the board and close the door.

    What type of material is the cover and pad?

    Both the cover and the pad are heavy duty and industrial grade designed for years of use. The cover is a 50/50 poly/cotton blend manufactured with a finish designed for steam irons. The pad is a 21 oz needle punch material that provides a level of cushioning preferred by our customers over the years.

    What are the electrical requirements?

    All electrical models are rated at 120V ac, 1500W max, 15 amps.

    Does the swivel board turn in both directions?

    When the ironing board is lowered, the swivel allows the board to turn 90 degrees in either direction until the board is parallel with the wall. Additionally, there are conveniently placed stopping points as the board is being turned.

    At what point does the board begin to swivel?

    The mid-point where our board begins to swivel is dependent upon the size of the cabinet. On the cabinets that hold our 46" board, the swivel point is 26 1/4" from the wall. On the cabinets that hold our 42" board, the swivel point is 26 5/8". (For actual measurements, please see the specifications for the model you are selecting.)

    Does the ironing board have to come down all the way before swiveling?

    The swivel mechanism does allow for the board to clear the cabinet allowing it to begin swiveling before it has been fully lowered. However, we recommend that you have the necessary clearance dimensions as shown in our specifications for the model that you are selecting.

    Product Reviews
    Overall Customer Rating:
    Customer Reviews: 1
    Ironaway A46
    Mike B.
    Herndon VA
    Review Date:

    I have the A46 with swivel and mirrored door. Great product. I was not sure about spending nearly $600 on a product that I had never seen before, but this turned out to be a good purchase. The order was delivered in about a week and was in perfect condition. It is quite heavy, which is nice because it is also well built. I was concerned that the ironing board would be flimsy when folded out, but it is quite a bit more sturdy during use than a regular free standing ironing board. It fold down and back up easily, with a nice balanced feel. The mirror for the door ships separately from the rest of the unit, but was easy to mount to the door. I painted the wood around the unit and the door then mounted to mirror to the door. The unit was easy to mount between the wall studs with the provided screws. The only thing I will add is a handle of some kind to make the door easier to open. I installed the unit myself. The wiring requires only basic wiring knowledge, but that depends on individual capability. Yes, this product is expensive. However, it is a quality product, the installation instructions are clear, and using this ironing board could not be more convenient. I like it a lot.
    Home Products Inc.
    Ph: 866.368.8663
    Hrs: MON-THU 8am to 5pm
            FRI 8am to 4:30pm PST
    Broan® and NuTone® are trademarks of Broan-NuTone, LLC,
    its subsidiaries and affiliates.
    All other brands are trademarks of their respective owners.

    © 2011 Q2U, LLC a limited liability company. All Rights Reserved.